A planar limestone bed has a true dip of 30° toward N45°E. What is the apparent dip angle along an exploratory cut oriented due North?
Breadth Physical Structural Geology
Question · Medium
An exploratory trench reveals a normal fault dipping at 60° with a net dip-slip displacement of 40.0 m. Assuming no strike-slip component, what are the fault heave and throw?
Question · Easy
According to Anderson's dynamical classification of faulting, which principal stress state corresponds to a strike-slip fault regime?
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
Two vertical conjugate shear joint sets in competent sandstone strike N30°E and N70°E. Assuming Coulomb failure criteria, what is the horizontal trend of the maximum principal compressive stress (σ1)?
A vertical exploratory borehole penetrates an ore-bearing sandstone formation that dips uniformly at 35°. The length of core intercepted through the formation is 48.0 m. What is the true stratigraphic thickness of the formation?
Which term describes an unconformity where horizontally deposited sedimentary strata lie directly upon tilted, folded, and eroded older sedimentary rocks?
A regional anticline has an interlimb angle measured between tangents at inflection points of 55°. According to Fleuty's (1964) fold classification, how is this fold classified?
A seismic refraction survey over flat bedrock yields a direct wave velocity of V1 = 1800 m/s and a refracted wave velocity of V2 = 3600 m/s. If the intercept time (t0) on the refracted arrival curve is 30.0 ms, what is the depth to the bedrock interface?
Question · Hard
Two fracture planes have perpendicular strikes: one strikes 000° and dips 45° East; the other strikes 090° and dips 45° South. What are the plunge and trend of their intersection line?
A fault surface preserves a clear slickenline but no independently verified asymmetric steps or other sense indicators. What can the lineation establish by itself?
In structural stress tensor inversion, the stress ratio is defined as R = (σ2 − σ3) / (σ1 − σ3). What geological stress state is indicated when R approaches 0.1?
In a regional seismic reflection section, a fault plane dips 50° and the hanging wall block shows stratigraphy displaced downwards relative to the footwall block. This structure is classified as a:
In two exploratory test pits, a sandstone bed exhibits an apparent dip of 20° along azimuth 030° and an identical apparent dip of 20° along azimuth 090°. What is the true dip direction of the bed?
Three exploratory boreholes intersect the planar top of a key marker bed: • Borehole A at (0 m E, 0 m N): marker elevation = 400.0 m • Borehole B at (100.0 m E, 0 m N): marker elevation = 400.0 m • Borehole C at (0 m E, 100.0 m N): marker elevation = 342.3 m What are the strike and true dip of the marker bed?
A planar geological contact is horizontal and crosses a valley on a topographic map. What relation should its outcrop trace have to elevation contours, ignoring cover and map error?
Which of the following correctly lists minerals in order of increasing relative hardness on the Mohs scale?
Breadth Mineralogy Petrology
A dense vein mineral sample consists of 60% quartz (density = 2.65 g/cm³) and 40% galena (density = 7.50 g/cm³) by volume. Neglecting porosity, what is the theoretical bulk dry specific gravity of the rock specimen?
Along the discontinuous branch of Bowen's reaction series, which ferromagnesian mineral crystallizes first at the highest temperatures from a cooling basaltic magma?
A plutonic rock has a modal mineral composition normalized to Quartz (Q), Alkali feldspar (A), and Plagioclase (P) of: Q = 35%, A = 45%, and P = 20%. Under the IUGS QAPF classification system, how is this rock classified?
Which clay mineral group has an expanding 2:1 sheet crystal structure with weak interlayer bonds, causing it to display the highest swelling potential and liquid limit in foundation engineering?
A feldspar in thin section shows repeated parallel albite twin lamellae under crossed polars. Which identification is most strongly supported by this common diagnostic feature?
A sandstone contains 80% framework quartz, 14% feldspar, and 6% lithic fragments, with less than 5% mud matrix. In the Folk Q-F-R classification, what is its name?
The diagnostic mineral assemblage glaucophane + lawsonite + jadeite characterizes which metamorphic facies, and under what tectonic conditions does it develop?
A diametral point load test on an NX-size drill core (diameter D = 54.0 mm) of fresh granodiorite fails at a load of P = 18.0 kN. Using the size-correction formula Is(50) = (D / 50)^0.45 · Is, and the empirical conversion UCS = 24 · Is(50), what is the estimated unconfined compressive strength?
In the olivine solid solution series (Fo-Fa), an olivine crystal has the stoichiometry (Mg0.80Fe0.20)2SiO4. Given atomic weights: Mg = 24.31, Fe = 55.85, Si = 28.09, O = 16.00, what is the weight percentage of FeO in this olivine?
An X-ray diffraction (XRD) analysis using Cu-Kα radiation (λ = 1.5418 Å) records a first-order (n = 1) basal reflection for kaolinite at 2θ = 12.35° (θ = 6.175°). According to Bragg's Law, what is the basal layer d-spacing (d001)?
In the classic increasing-grade Barrovian index-mineral sequence for pelitic rocks, which listed mineral follows garnet and precedes kyanite?
Under the Dunham (1962) classification of carbonate rocks, what term is assigned to a limestone whose original components were organically bound and encrusted together during deposition (such as in a coral reef framework)?
A standard two-cycle slake durability test (ASTM D4644) on weak mudstone fragments starts with an initial oven-dry mass of 500.0 g. After the first 10-minute cycle, the retained dry mass is 410.0 g; after the second 10-minute cycle, the retained dry mass is 345.0 g. What is the slake durability index (Id2) and its Gamble (1971) durability classification?
Among the three Al2SiO5 aluminosilicate polymorphs (andalusite, kyanite, sillimanite), which mineral is thermodynamically stable exclusively under high-temperature conditions exceeding ~500°C–700°C across a wide pressure range?
A saturated clay deposit has a total unit weight of γsat = 19.5 kN/m³. The groundwater table is located at the ground surface. Using γw = 9.81 kN/m³, what is the vertical effective stress (σ'v) at a depth of 8.0 m?
Depth Geotechnics Soil Mechanics
A consolidated drained triaxial compression test on dense silty sand yields an effective cohesion of c' = 15.0 kPa and an effective angle of internal friction of φ' = 32°. On a potential shear plane where the effective normal stress is σ'n = 120.0 kPa, what is the available shear strength (τf)?
A continuous strip footing has B=2.0 m and Df=1.5 m in dry cohesionless sand of unit weight 18 kN/m³, with groundwater sufficiently deep to have no effect. Using qult = qNq + 0.5γBNγ, Nq=18.4 and Nγ=22.4, what ultimate bearing pressure is calculated?
A vertical frictionless wall yields enough to mobilize active conditions in level dry cohesionless backfill. With H=6.0 m, γ=17.5 kN/m³, and φ=30°, what Rankine active thrust acts per meter of wall?
For level cohesionless backfill against a vertical smooth wall, with sufficient movement to mobilize passive conditions and φ'=34°, what is Rankine Kp?
A normally consolidated clay stratum has a thickness H = 4.0 m, initial void ratio e0 = 0.85, and compression index Cc = 0.30. The initial in-situ vertical effective stress at the layer mid-depth is σ'0 = 100.0 kPa. A foundation load increases the effective stress by Δσ' = 60.0 kPa. What is the ultimate primary consolidation settlement (Sc)?
For a normally consolidated clay deposit with an effective internal friction angle of φ' = 26°, what is the coefficient of lateral earth pressure at rest (K0) estimated using Jaky's empirical equation?
A cohesionless colluvial slope (c' = 0) has an internal friction angle φ' = 36° and saturated unit weight γsat = 20.0 kN/m³. Steady seepage flows parallel to the slope face with the phreatic surface at the ground surface (γw = 9.81 kN/m³). What is the maximum slope angle (βmax) for a factor of safety of FS = 1.0?
A Standard Penetration Test (SPT) is performed using a safety hammer that delivers an actual measured hammer energy ratio of ER = 45%. If the raw field blow count is recorded as N = 24, what is the standardized energy-corrected blow count (N60)?
An inorganic soil has 65% passing the No. 200 sieve, liquid limit 58%, and plasticity index 26%. Under the USCS plasticity chart, what is its group symbol?
A falling-head permeameter test is conducted on a cylindrical soil specimen of length L = 15.0 cm and diameter D = 10.0 cm (cross-sectional area A = 78.54 cm²). The standpipe cross-sectional area is a = 0.50 cm². The hydraulic head drops from h1 = 60.0 cm to h2 = 30.0 cm in a duration of t = 180 seconds. What is the hydraulic conductivity (k) of the specimen?
A fine sand deposit has a specific gravity of soil solids Gs = 2.68 and an in-situ void ratio e = 0.68. At what critical hydraulic gradient (ic) will upward seepage force the effective stress to zero, inducing a quicksand (boiling) condition?
An undisturbed sample of clay taken from 6.0 m depth is currently subjected to an effective overburden stress of σ'v0 = 80.0 kPa. An oedometer test evaluated using Casagrande's method determines a preconsolidation pressure of σ'p = 240.0 kPa. What is the Overconsolidation Ratio (OCR) and stress history?
Which combination of geotechnical and geological conditions exhibits the highest susceptibility to liquefaction during severe earthquake ground motions?
In a Proctor compaction test, a soil has specific gravity of solids Gs = 2.70. At a gravimetric moisture content of w = 15.0%, what is the theoretical maximum dry unit weight on the Zero Air Voids (ZAV, 100% saturation) curve? (γw = 9.81 kN/m³)
An undrained triaxial compression test is conducted on a fully saturated specimen of normally consolidated clay (Skempton's B = 1.0). The cell confining pressure is increased by Δσ3 = 50.0 kPa, and the axial deviator stress is subsequently increased by Δ(σ1 − σ3) = 120.0 kPa to failure. If Skempton's pore pressure parameter A at failure is 0.75, what is the total excess pore water pressure (Δu) generated?
A clay sample from a borehole has a Liquid Limit of LL = 45%, a Plastic Limit of PL = 20%, and a natural in-situ moisture content of wn = 25%. What is the Liquidity Index (LI) of this clay?
Loading more…