Evaluate the definite integral ∫₀² (3x² + 2) dx.
Mathematics Statistics
Question · Easy
A sample of five concrete cylinder strengths (MPa) is 22, 24, 26, 28, 30. What is the sample standard deviation (n−1 denominator)?
For matrix [[4, 1], [2, 3]], what is the larger eigenvalue?
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
Two variables have Pearson correlation r = −0.85. This indicates:
Question · Medium
A 10 kN vertical force acts at the free end of a 2 m cantilever. The fixed-end bending moment magnitude is:
Engineering Mechanics
A projectile is launched horizontally at 20 m/s from a 45 m high cliff (g = 10 m/s²). Time to reach ground (neglect air resistance) is:
A 5 kN block rests on a horizontal plane with coefficient of static friction μₛ = 0.4. Maximum horizontal force to start motion is:
A wheel of radius 0.5 m rotates at 120 rpm. Its rim linear speed is approximately:
A whole-circle bearing of 225° converts to a reduced bearing (quadrant notation) of:
Surveying
Question · Hard
A levelling staff reading of 1.850 m is taken on a benchmark RL 100.000 m with the instrument at unknown height. If the next reading on a point is 2.450 m, the RL of that point is:
In a closed traverse of four sides, measured interior angles sum to 360°02′. The angular misclosure is:
For nominal M25 concrete, the target mean compressive strength at 28 days (per IS/ACI-style QC) is typically above 25 MPa by about:
Materials Construction
Grade Fe 415 reinforcing steel in Pakistan practice denotes minimum yield strength of approximately:
First-class burnt-clay bricks used in load-bearing masonry typically require minimum compressive strength on the order of:
Excess water in a concrete mix primarily:
Well-graded aggregate for concrete improves:
Water flows in a horizontal pipe. By Bernoulli (neglect losses), if velocity doubles, static pressure:
Fluid Mechanics
Manning equation Q = (1/n) A R^(2/3) S^(1/2) uses R as:
Water at 20°C flows in a 100 mm diameter pipe at 1.5 m/s. Reynolds number is approximately:
In Darcy–Weisbach, head loss hf = f (L/D)(V²/2g). If length doubles while other terms stay constant, hf:
A steel bar (E = 200 GPa) of length 2 m and area 500 mm² carries axial load 100 kN. Axial deformation is:
Mechanics Of Solids
A rectangular section 300 mm × 500 mm (depth vertical) has second moment of area I about the horizontal centroidal axis:
A solid circular shaft of diameter 100 mm transmits torque 5 kN·m. Maximum shear stress (torsion formula) is approximately:
On Mohr’s circle, the center lies at normal stress:
The depth of 50 mm rainfall over a 20 km² catchment equals a runoff volume of:
Hydrology Water Resources
In an IDF curve, for a fixed rainfall duration, intensity generally ______ as return period increases.
A 3-hour unit hydrograph has peak discharge 120 m³/s from 1 cm effective rainfall over 500 km². The peak ordinate represents:
A reservoir has surface area 4 km² and average depth 12 m. Gross storage capacity is:
For uniform flow in a wide rectangular channel, Manning n = 0.02, slope S = 0.0004, depth y = 1.0 m, discharge per unit width q ≈:
Cropping intensity of 150% on a net cultivated area of 100 ha implies gross cropped area of:
Delta (Δ) in irrigation is defined as:
Over a broad-crested weir, critical flow depth occurs when Froude number Fr equals:
Horton infiltration equation models infiltration rate as:
Pan evaporation is 8 mm/day and pan coefficient K_p = 0.7. Estimated lake evaporation is:
A 100-year flood has annual exceedance probability of:
The S-curve hydrograph is obtained by:
SPT N-value of 30 in medium dense sand typically indicates:
Geotechnical Engineering
Standard Proctor test determines:
Primary consolidation settlement is chiefly driven by:
Terzaghi bearing capacity for a strip footing includes terms for cohesion, surcharge, and:
Factor of safety for infinite slope in cohesionless soil depends on:
Rankine active earth pressure coefficient Ka for φ = 30° is:
Passive earth pressure is generally:
Darcy’s law for laminar flow in soils is:
A constant-head permeability test is most suitable for:
End-bearing pile capacity in rock primarily relies on:
Immediate settlement of a footing on sand is often estimated using:
Loading more…