Under Sri Lanka Standard SLS 39, what is the standard dimension of a common burnt clay building brick?
Brickwork
Question · Medium
What is the primary function of a queen closer in a brick wall?
Question · Easy
Which of the following describes an English bond in brick masonry?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
In Flemish bond, what is the arrangement of bricks in each course?
According to CIDA (Construction Industry Development Authority) guidelines in Sri Lanka, what is the standard recommended thickness of a mortar joint in brick masonry?
What is the concave indentation on the top surface of a clay brick called, and how should it be positioned when laid?
Using an estimating module of one SLS 39 brick (220 mm x 105 mm x 65 mm) plus a 10 mm mortar joint in each direction, approximately how many bricks occupy 1 cubic meter of brick masonry?
Question · Hard
What is a king closer in brick masonry?
For a wall constructed entirely of stretchers (stretcher bond), what is the maximum structural thickness of the wall?
What is the practice of leaving stepped projections at the end of a brick wall to allow for future horizontal extension called?
Why are mortar joints 'raked out' to a depth of about 12 mm to 15 mm while the mortar is still green?
At which level of a building structure is a Damp Proof Course (DPC) typically placed?
If 1 cubic meter of brick masonry requires approximately 30% of its volume as mortar, calculate the approximate total dry volume of the cement-sand mixture required to prepare this mortar for a 1:4 mix ratio. (Use a dry volume conversion factor of 1.33 for mortar).
Why must clay bricks be thoroughly soaked in clean water before they are laid in cement mortar?
What is the white, powdery deposit that sometimes appears on the surface of brick walls called, and what causes it?
What is the purpose of placing thin galvanized steel strips, commonly known as hoop iron, in horizontal mortar joints of a brick wall?
Which of the following operations is performed first when starting to build a brick wall between two existing columns?
What is the difference between a header and a stretcher?
Before choosing the width and type of block for a wall, what should an NVQ Level 3 mason do?
Blockwork
When comparing hollow and solid cement blocks of similar face size, which statement is generally correct?
Using a nominal block face module of 400 mm x 200 mm, how many modules cover a wall 8 m long and 3 m high before openings and waste allowance?
How should the cement-to-sand proportion for block-laying mortar be selected and batched?
What is the primary purpose of inserting wall ties (usually hoop iron or steel bars) into concrete columns where they meet a block wall?
A drawing shows the required end bearing for a lintel over a block-wall opening. What should the mason do?
What is the term for filling the vertical hollow cores of concrete blocks with concrete grout, often incorporating steel reinforcing bars, at corners or regular intervals?
When setting out the first course of a block wall, which action best supports accurate work?
Which check is appropriate before concrete blocks are accepted for laying?
How should a mason decide how high to raise fresh blockwork during a work period?
Why are the block grooves and joints cleaned and properly filled with cement-sand mortar during block laying?
A block wall begins to move out of plumb while the mortar is still fresh. What is the correct response?
In a standard nominal concrete mix ratio of 1:2:4, what do the three numbers represent, in order?
Concrete Technology
What is the main purpose of a lean-concrete blinding layer below a reinforced foundation?
What is the primary purpose of performing a concrete slump test on a construction site?
A slump result is outside the range specified for a concrete pour. What should the mason do?
Calculate the volume of concrete required to cast a reinforced concrete slab that is 6 meters long, 4 meters wide, and has a thickness of 120 mm.
What determines the required clear concrete cover to reinforcement in a column?
What is the primary purpose of correctly sized cover blocks or spacers under slab reinforcement?
Before concrete is placed in a footing, which reinforcement-cover check is correct?
How should the curing method and duration for newly placed concrete be determined?
What is the primary danger of adding excessive water to a concrete mix to make it easier to pour?
What is the correct method for compacting concrete using an internal mechanical poker vibrator?
Assuming a dry-volume factor of 1.54 for concrete, approximately how many 50 kg bag-equivalents of cement does 1 cubic meter of wet concrete contain at a 1:2:4 ratio if each bag occupies 0.035 m3?
Which curing method can maintain continuous direct water contact on a flat horizontal concrete slab?
Why is steel reinforcement embedded in concrete structures?
When concrete must be placed at a level well below the delivery point, what is the correct approach?
How should the maximum coarse-aggregate size for reinforced concrete be selected?
If a concrete mix specification calls for a water-cement ratio of 0.50 by weight, how much water (in liters) must be added for each 50 kg bag of cement?
Loading more…