Which welding helmet auto-darkening shade range is appropriate for short-circuit GMA (MIG) welding on 18-gauge automotive steel?
Welding Safety
Question · Easy
Why should a welder avoid pants with rolled cuffs when performing GMA welding?
What does PPE stand for in welding safety?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
Which standard primarily addresses arc welding of automotive steel weld quality?
Question · Medium
Which AWS code provides sheet-steel welding requirements that I-CAR aligns with for destructive testing terminology?
When GMA welding inside a vehicle, what is the primary reason to disconnect the battery?
Vehicle Specific Procedures
Where should the work clamp (ground) be placed when welding on a vehicle?
Standard shielding gas for GMA (MIG) welding steel in automotive collision repair is:
Shielding Gases
Which solid wire is the most common consumable for GMA welding mild steel in automotive collision repair?
Which polarity is standard for GMA welding (GMAW)?
Equipment Setup
Which gas regulator measurement is most relevant to short-circuit GMA welding on 18-gauge steel?
Which best describes 'contact-tip-to-work distance' (CTWD)?
Increasing electrical stickout (longer wire past the contact tip) while keeping other settings constant generally:
Which transfer mode is typical of GMA welding on 18-gauge collision steel?
Gma Welding Process
For short-circuit GMA on thin steel, which travel technique generally yields less penetration and lower burn-through risk?
Which adjustment most directly controls bead width and arc length on a GMA machine?
On a constant-voltage (CV) GMAW power source, increasing wire-feed speed while voltage is held constant:
Which weld is required as part of the SWQT performance test?
Weld Joints
How many welds are produced in total during the SWQT performance test?
Which two welding positions are tested on the SWQT?
What gauge of automotive electrogalvanized steel does I-CAR specify for SWQT practice coupons?
Materials Handling
About how long is the equipment-familiarization period before the timed SWQT welds?
How long does the candidate have to complete the timed vertical-position welds on the SWQT?
How often must the I-CAR welding qualification be renewed?
Weld Testing And Inspection
Which I-CAR shop designation requires structural technicians to hold current welding qualifications?
Which sequence best describes preparing 18-gauge electrogalvanized coupons before welding?
What is a typical contact-tip-to-work distance for short-circuit GMA on 18-gauge steel?
Which is a defining feature of a plug weld used in collision repair?
STRSW stands for which welding process used in collision repair?
Which weld joins two overlapping sheets along the edge of the top sheet?
Which weld joins two sheets edge-to-edge in the same plane?
Why is a backing strip sometimes used behind a butt joint when GMA welding thin steel?
Which I-CAR-specified weld length is required on the butt joint with backing during the SWQT?
Question · Hard
Which weld appearance most often indicates a 'cold' GMA weld on thin steel?
Weld Defects
Which is a likely cause of porosity in a GMA weld on steel?
Which best defines undercut as a GMA weld defect?
Burn-through (melt-through) on 18-gauge steel is most likely caused by:
Cold lap (lack of fusion) on a GMA weld means:
Which destructive test is used to evaluate a plug weld on a lap joint in the SWQT?
After a passing plug-weld twist test, where should the nugget tear out?
What minimum tear-out diameter does I-CAR specify for a passing plug-weld twist test?
Which destructive test is used to evaluate a fillet weld on a lap joint?
What does it mean when a destructive test causes the base metal to fail before the weld?
Visual inspection of SWQT welds is performed using criteria from:
AHSS stands for:
Steel Types And Properties
Which steel is highly heat-sensitive and is generally welded only at OEM-specified locations because heat reduces its strength?
Dual-phase steel gets its strength primarily from a microstructure of:
Loading more…