Which steel category typically refers to grades with tensile strength of 600 MPa or higher?
Vehicle Construction Materials
Question · Easy
Why is heat-straightening NOT permitted on boron-alloyed press-hardened steel parts?
Question · Medium
According to I-CAR Repairability Summit best practice, parts with tensile strength over 600 MPa should generally only be replaced how?
Sectioning Procedures
Trades Exam Prep Podcast
Listen on Spotify
Podcast
What is the I-CAR welding qualification test for structural steel GMA (MIG) welding called?
Structural Welding
Which weld qualification test is required when a Structural Technician performs GMA welding on aluminum-intensive vehicles?
What is the PRIMARY purpose of anchoring a damaged vehicle before pulling?
Anchoring And Measuring
Which measuring system uses a moving probe arm or laser to capture vehicle dimensions in three axes?
What is the term for the reference plane from which vertical (height) measurements are taken on a vehicle?
What is the FIRST measurement that should be made during structural damage analysis?
On a sectioned full-body replacement, where are OEM-recommended sectioning joints typically located?
Which adhesive system combines a structural adhesive with welds or rivets at attachment points?
Structural Fasteners
What does SPR stand for in structural collision repair?
Where must a structural technician look up the specific sectioning procedure for a given vehicle?
Oem Repair Procedures
Which type of corrosion protection is sprayed inside enclosed structural cavities such as rocker panels and pillars after sectioning?
Corrosion Protection
Which primer is most commonly specified by OEMs as the first coating over bare steel weld zones?
Before working near an electric vehicle (EV) high-voltage battery pack during structural repair, what is the first required step?
Ev Structural Considerations
After replacing or removing any deployed supplemental restraint system (SRS) component, the technician must:
Restraint Systems
What does the I-CAR Gold Class designation indicate about a collision repair shop?
Which method is the appropriate way to straighten cold-rolled mild steel that has not been hardened?
Which I-CAR role pathway requires SWQT, weld bonding/rivet bonding training, and structural sectioning courses?
When sectioning a steel rocker panel at an OEM-approved location, which weld profile is most commonly specified at the joint?
Which structural steel category is generally considered acceptable for limited cold-mechanical straightening per most OEM procedures?
What is the function of weld-through primer applied to mating flanges before GMA plug welding?
When performing structural welds, which GMA welding shielding gas blend is most commonly specified for sheet steel?
What is the SWQT requirement for weld positions during testing?
Why must aluminum GMA welding generally use pulse-transfer mode equipment?
Why must aluminum repair tools be kept physically separated from steel repair tools?
Question · Hard
What is the term for completely replacing a vehicle's body shell at all factory seams rather than sectioning?
Full Body Replacement
Which tool is used to remove factory resistance spot welds when separating panels for full-body replacement?
What recommended drill speed range applies to boron-alloyed steel when using special carbide drill bits to remove spot welds?
What is the purpose of a vehicle's anti-flutter foam (sometimes called expandable structural foam) inside a pillar or rocker?
After completing a structural weld, what visual inspection criterion is used to assess weld quality?
Which two adhesive brands are most commonly cited in I-CAR coursework for structural collision adhesives?
What is the purpose of seam sealer applied along welded body joints after sectioning?
Which document does a Structural Technician consult for OEM-approved sectioning and weld procedure on a specific vehicle?
How often is I-CAR welding certification typically renewed?
Which factory body manual term refers to a designated reinforcement that supplements a sectioned joint?
When are vehicle anchor points clamped for pulling?
What does a measurement showing a 'mash' indicate?
What does a measurement showing 'diamond' damage indicate?
After completing structural repairs on a vehicle equipped with ADAS (advanced driver assistance systems), what step is typically required?
During a full-body replacement on an EV, when can the high-voltage battery pack typically be reinstalled?
Which type of welder is required for squeeze-type resistance spot welding (STRSW) on modern UHSS-equipped vehicles?
Why is the heat-affected zone (HAZ) a concern when welding UHSS?
A rivet bonding repair requires:
What is a flow-drill screw (FDS) used for in modern collision repair?
When sectioning is permitted, what is the typical maximum number of sectioning joints per part allowed by OEMs?
Loading more…