On a packaged rooftop unit with an economizer, what condition allows the economizer to provide 'free cooling'?
Rooftop Units Economizers
Question · Easy
A dry-bulb economizer uses a single outdoor sensor for changeover. Compared with an enthalpy economizer, the dry-bulb type can waste energy when outdoor air is:
Question · Medium
What is the purpose of the minimum-position setting on an economizer's outdoor-air damper?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
Modern rooftop economizer controllers include Fault Detection and Diagnostics (FDD). A common FDD fault is:
On a gas/electric packaged rooftop unit, the 'gas' and 'electric' refer respectively to:
A heat-pump packaged rooftop unit uses which component to reverse refrigerant flow between heating and cooling modes?
During an integrated economizer cycle, the controller stages on mechanical cooling while the economizer remains at maximum open. This indicates:
An enthalpy economizer compares outdoor and return-air conditions. Enthalpy is a measure of:
A rooftop economizer is stuck at minimum position on a cool 55 degrees F day with a cooling call. The most likely cause is:
Question · Hard
Demand Control Ventilation (DCV) on a rooftop economizer typically modulates the outdoor-air damper based on:
Multi Stage Zone Controls
A two-stage cooling rooftop unit brings on the second compressor stage when:
In a constant-volume multi-zone rooftop system using a single supply temperature, individual zone temperature is most commonly controlled by:
In a Variable Air Volume (VAV) system, the supply fan typically maintains a constant:
A light commercial control transformer steps 208/230V line voltage down to operate the control circuit at:
On a typical 24V cooling control, which thermostat terminal energizes the compressor contactor through the unit's low-voltage circuit?
A Direct Digital Control (DDC) sequence of operation on a rooftop unit is best described as:
A time clock or scheduling function on a commercial rooftop controller is primarily used to:
A light commercial rooftop scroll compressor circuit uses head-pressure control in winter primarily to:
Refrigeration Circuit Head Pressure
One common method of low-ambient head-pressure control on an air-cooled condenser is:
Two scroll compressors are piped in a tandem (manifolded) arrangement on one circuit. A key benefit is:
Why must a scroll compressor never be operated even briefly with reversed phase rotation (on a 3-phase unit)?
A semi-hermetic compressor differs from a hermetic compressor in that it:
A liquid-line solenoid valve used for pump-down control closes on the off cycle to:
On an R-410A light commercial system operating normally, which statement about pressures is correct compared with R-22?
A field technician finds higher-than-normal head pressure, normal-to-high subcooling, and normal superheat on a rooftop unit. The most likely cause is:
Light commercial cooling airflow is commonly designed at approximately how much supply CFM per ton of cooling?
Airflow Psychrometrics Fan Laws
A 5-ton rooftop unit is designed for 400 CFM per ton. What total supply airflow should it deliver?
External Static Pressure (ESP) on a rooftop unit is best defined as:
A technician measures +0.45 in. w.c. in the supply plenum and -0.35 in. w.c. in the return. What is the total external static pressure?
According to the first fan law, if blower speed (RPM) is increased by 20% with the same system, airflow (CFM) will:
Using the fan laws, if airflow is increased by 25% (CFM ratio 1.25), the required brake horsepower changes by approximately a factor of:
On a belt-drive blower, increasing airflow by installing a larger-diameter motor (drive) pulley will:
Compared with a belt-drive blower, a direct-drive (ECM) blower in modern rooftop units typically offers:
Using the sensible heat formula Qs = 1.08 x CFM x deltaT, a rooftop unit moving 2,000 CFM with a 20 degrees F temperature drop across the coil produces approximately:
On a properly operating cooling coil, the relationship between dry-bulb and wet-bulb temperatures of the air leaving the coil shows that:
A rooftop unit is delivering far less airflow than design and the evaporator coil is icing. Of these, the most likely air-side cause is:
On a 3-phase, 4-wire wye system, the line-to-line voltage is 480V. The approximate line-to-neutral voltage is:
Electrical Charging Maintenance
A phase monitor (phase protection relay) on a 3-phase rooftop unit protects the compressor by opening the control circuit on:
A 3-phase motor is single-phasing (one line lost) while running. The typical immediate symptom is:
Real (true) power for a balanced 3-phase load is calculated as:
A contactor in a rooftop unit primarily functions to:
An overload device protects a motor primarily against:
To reverse the rotation of a 3-phase motor (for example, after finding a scroll compressor running backward), a technician should:
Acceptable 3-phase voltage imbalance is generally limited to no more than about:
On a fixed-orifice (piston) light commercial system, the most reliable charging method is by:
On a TXV (thermostatic expansion valve) system, the preferred method to verify charge is:
Superheat is calculated as:
Loading more…