On a standard residential air-source heat pump that uses an O-terminal thermostat, when is the reversing-valve solenoid coil energized?
Controls Sequence
Question · Medium
What is the primary purpose of the suction-line accumulator in a heat pump?
Reversing Cycle Components
Question · Easy
In heating mode, which coil of an air-source heat pump acts as the evaporator?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
A heat pump has a measured heating output of 30,000 Btu/h while drawing 3,000 watts of electrical power. What is its coefficient of performance (COP)?
Capacity Charging Airflow
Question · Hard
The point at which a heat pump's heating capacity exactly equals the building's heat loss is called the:
Why does an air-source heat pump's heating capacity decrease as the outdoor temperature drops?
During a defrost cycle on an air-source heat pump, the system normally:
Defrost Systems Controls
A demand-defrost control initiates a defrost cycle based on:
What component allows a single thermostatic expansion valve assembly to meter correctly in one direction while letting refrigerant bypass it in the other direction of flow?
Which efficiency rating describes the seasonal heating performance of an air-source heat pump?
On a heat pump installed with an O-terminal thermostat, the reversing valve solenoid fails open (coil burned out). What symptom is most likely?
Geothermal Dualfuel Troubleshooting
Emergency heat mode on a heat pump thermostat does what?
A building has a design heat loss of 36,000 Btu/h at 5 degrees F. The heat pump delivers 24,000 Btu/h at 5 degrees F. How much supplemental heat capacity is required at that condition?
Many manufacturers specify charging an air-source heat pump in heating mode by:
What is the typical required indoor airflow across the coil of a heat pump, expressed per ton of capacity?
On a heat-pump thermostat, what is the function of the B terminal?
A geothermal (water-source) heat pump using a closed-loop ground system circulates:
In a dual-fuel (hybrid) system, the outdoor thermostat or control's main job is to:
Which statement about SEER and HSPF is correct?
A heat pump in heating mode shows very high head pressure and the indoor air is barely warm. The most likely airflow-related cause is:
Which device protects the compressor by keeping refrigerant oil warm and reducing migration during the off cycle, which is especially important in cold-climate heat pumps?
What does the term 'bi-flow filter-drier' mean in a heat pump?
A heat pump at 47 degrees F outdoor delivers 36,000 Btu/h. At 17 degrees F outdoor it delivers 24,000 Btu/h. This relationship illustrates that:
On a time-and-temperature defrost board, what two conditions must typically both be satisfied to initiate defrost?
What most commonly terminates a defrost cycle on a properly working heat pump?
Auxiliary (supplemental) heat on a heat pump should normally be staged on when:
An outdoor thermostat (lockout thermostat) is often added to a heat-pump system to:
A fixed-orifice (piston) air-source heat pump is best charged in cooling mode by:
The reversing valve in a heat pump shifts position primarily because of:
A customer complains of high electric bills and lukewarm air in mild weather (45 degrees F outdoor). You find the strip heaters energize every heat call. The most likely cause is:
Which refrigerant-side condition typically indicates a heat pump is undercharged while operating in heating mode?
A heat pump at 35 degrees F outdoor delivers a COP of 3.0. Approximately how many Btu/h of heat does it deliver for each 1,000 watts of electrical input?
In cooling mode, on an O-terminal residential heat pump, the indoor coil functions as the:
Frost forms on a heat pump's outdoor coil in heating mode mainly because:
A technician measures a heat pump heating output of 27,300 Btu/h with the compressor and fans drawing 2,400 watts. What is the COP (rounded to one decimal)?
What is the most likely result of a reversing valve that is stuck partway between positions (slide not fully shifted)?
On a heat-pump thermostat, which terminal energizes the compressor contactor for both heating and cooling?
An open-loop (pump-and-dump) water-source heat pump differs from a closed-loop system in that it:
Which is true about the COP of a properly sized ground-source (geothermal) heat pump compared with an air-source unit in cold weather?
During defrost, why is auxiliary electric heat usually energized?
A heat pump runs continuously in heating but the home never reaches setpoint, even though refrigerant pressures and airflow are normal and it is 10 degrees F outside. The most likely explanation is:
Which statement correctly describes the relationship between COP and HSPF?
A defrost board's outdoor coil sensor (defrost thermostat) has failed open (reads as always warm). What symptom results?
Which of the following best describes a 'bivalent' or switchover temperature in a dual-fuel system?
Why must a heat pump's metering device control flow correctly in both directions, unlike a straight air conditioner?
A heat pump's COP in heating mode is 3.2. A pure electric-resistance furnace has an effective COP of:
When a heat pump is in cooling and the outdoor coil is the condenser, the outdoor fan should:
Loading more…