Which safety device must always be placed under a raised motor vehicle before an auto mechanic works underneath it?
Basic Metal Work
Question · Easy
Spongy brake pedal?
Short
Which precision measuring tool is used to measure the outside diameter of an engine crankshaft main journal with an accuracy of 0.01 mm?
What is the reading on a standard metric outside micrometer when the sleeve shows 25.5 mm and the thimble line 32 aligns with the index line?
Question · Hard
Trades Exam Prep Podcast
Listen on Spotify
Podcast
Which tool is used in conjunction with a straight edge to measure cylinder head warpage across the gasket mating surface?
Question · Medium
What is the primary purpose of using a centre punch before drilling a hole in a mild steel bracket?
What is the point angle of a standard prick punch used for precise layout marking compared to a centre punch?
Which hand file has teeth running in only one diagonal direction across its face?
What is the correct procedure for cleaning metal particles (pinning) trapped between the teeth of a file?
Which tap in a standard three-piece hand tap set has the longest taper (approximately 8 to 10 threads) for starting a thread in a drilled hole?
What is the tapping drill size (TDS) required to tap an M10 x 1.5 standard metric coarse internal thread in mild steel?
When tapping an internal thread by hand, why must the tap wrench be reversed approximately half a turn after every full forward cutting turn?
Which tool is used to cut external threads onto the end of a solid steel rod or shaft by hand?
What is the primary method for repairing stripped female internal threads in an aluminum engine block cylinder head bolt hole?
Which type of cold chisel is specifically ground for cutting narrow keyways, slots, and square grooves in metal components?
What is the recommended point angle of a standard twist drill bit used for general drilling in mild steel and cast iron?
What happens if a twist drill bit is operated at excessive rotational speed without adequate cutting lubricant?
Which tool is used to measure the axial end-play (float) of an automotive engine crankshaft or camshaft?
What is the purpose of using soft copper or aluminum vice jaws (vice clamps) when clamping precision machined automotive parts?
Which tool is designed to tighten cylinder head bolts and main bearing cap bolts to exact manufacturer specified torque values?
What does a torque angle gauge (degree wheel) measure during modern engine cylinder head bolt tightening procedures?
What is the primary function of an engineer's try square during metal marking out?
Why is marking blue (layout dye) applied to the surface of a metal workpiece before marking out?
Which tool is used to remove a broken bolt or stud that has sheared off below the surface of a threaded hole?
What is the purpose of a countersinking drill bit?
Which metric bolt marking indicates a high-tensile structural automotive fastener suitable for chassis and suspension components?
What is the primary function of a split spring lock washer (Grover washer) installed under a nut?
When using a pedestal grinding machine to sharpen cold chisels or drill bits, what is the maximum permissible clearance between the grinding wheel and the tool rest?
What is the purpose of performing a 'ring test' on a vitrified abrasive grinding wheel before mounting it on a grinder?
Which tool is used to measure the internal diameter of an engine cylinder bore at various depths to evaluate taper and out-of-round wear?
What is the purpose of using a telescoping gauge (snap gauge) in automotive measurement?
Which tool is used to accurately measure the gap between the electrodes of a spark plug?
What is the pitch of a standard metric M12 coarse thread according to ISO standards?
When sawing a piece of thick mild steel bar with a hand hacksaw, what is the correct cutting motion?
Which safety precaution must be observed when using compressed air to clean brake dust from vehicle drum brake assemblies?
What is the primary function of a pilot hole when drilling large diameter holes (e.g. greater than 12 mm) in thick steel plate?
Which hammer type is recommended for striking punches, cold chisels, and general metal shaping in an automotive workshop?
What is the danger of using a cold chisel or punch that has developed a 'mushroomed' head from repeated hammer blows?
Which tool is used to remove a stuck or press-fit ball bearing from an automotive gearbox shaft without damaging the shaft?
What is the function of a screw pitch gauge in the automotive workshop?
Which liquid chemical locking compound is applied to clean bolt threads to prevent vibrational loosening on brake caliper mounting bolts?
What is the primary function of a reamer used after drilling a hole in a metal component?
What is the correct sequence of events in a four-stroke internal combustion engine operating on the Otto cycle?
Automotive Practice
What is the position of the intake and exhaust valves during the compression stroke of a four-stroke engine?
How does a four-stroke diesel engine ignite its fuel charge compared to a petrol (gasoline) engine?
What is the primary function of the oil control ring (bottom ring) on an automotive engine piston?
What is the speed relationship between the engine crankshaft and the camshaft in a four-stroke engine?
Loading more…