A mild steel plate for a welding job measures 300 mm long and 150 mm wide. What is its area in square millimetres?
Basic Math And Measurement
Question · Easy
How many millimetres are there in 12.5 centimetres?
A welding job specification allows a root gap of 3 mm with a tolerance of plus or minus 10%. What is the maximum acceptable root gap?
Question · Medium
Trades Exam Prep Podcast
Listen on Spotify
Podcast
A welder mixes brazing flux paste in a ratio of 2 parts flux powder to 5 parts water by volume. How much water is needed for 40 mL of flux powder?
A fabrication drawing specifies four equal-length pipe sections cut from a 5.6 m pipe, allowing 40 mm total for cutting losses. What is the length of each section, in millimetres?
Question · Hard
Which piece of personal protective equipment specifically protects a welder's eyes and face from the intense ultraviolet and infrared radiation produced by an electric arc?
Occupational Safety And Health
What is the primary purpose of wearing leather gloves and a leather apron during arc welding?
A welder notices sharp eye pain, redness and a gritty sensation in the eyes several hours after welding without adequate eye protection. What condition does this most likely describe?
Why must an oxygen cylinder never be stored or used near oil or grease?
What is the correct immediate action if a flashback (flame burning back into the torch) occurs in an oxy-acetylene torch?
Which category of workplace hazard best describes exposure to welding fumes and gases produced during SMAW?
A welding workshop's OSH procedure requires each worker's 'fit to work' record to be updated regularly. Which document is specifically listed as part of this record?
In workplace housekeeping (5S-style) practice, what is the recommended first step before arranging items in a welding workshop?
Housekeeping And Workplace Organization
Which of the following is an example of a 'minor repair' a welder might perform on hand tools as part of routine housekeeping?
According to standard workplace housekeeping procedure, how should identification marks such as colour coding, labels or tags typically be used?
Why must safety equipment and evacuation passages be kept clear and accessible when arranging a welding workshop?
In the Light Engineering Sector, what is a key responsibility expected of an entry-level worker such as a welder when starting a new job task?
Light Engineering Sector Practices
Which of the following is described as an 'effective interpersonal skill' for working with others in a light engineering workshop?
When planning work activities in a team setting, what should be identified and clarified with the appropriate persons first?
Which category of hazard in a manufacturing or light engineering workplace refers to risks from moving machine parts and electrical equipment such as a welding power source?
A new worker in a light engineering workshop is unsure which specific task to perform among several possible assignments. According to sound workplace practice, what should the worker do before proceeding?
In engineering and technical drawings, what does a dimension typically indicate?
Technical Drawing Interpretation
Before starting work from a technical drawing, why must a welder first check that the correct drawing is selected and validated?
On a welded-joint drawing, a symbol consisting of a reference line, an arrow pointing to the joint, and a triangular symbol below the line most commonly represents which type of weld?
What does a tolerance value shown on a technical drawing tell a welder or fabricator?
When interpreting a technical drawing's material specification note, what information is the welder primarily looking for?
Which of the following is classified as an 'instruction' type of information that may appear on a technical drawing, according to the standard range of variables for interpreting drawings?
A technical drawing shows a welded assembly with a clearance or tolerance value that appears inconsistent with the workplace's normal fabrication standard for that joint. What should the welder do first, according to correct technical-drawing interpretation practice?
Which of these is a hand tool commonly used by a welder to remove slag and clean weld beads by striking?
Hand And Power Tools
What is the correct first step before using either a hand tool or a power tool in the workshop, according to standard practice?
Which power tool would a welder most likely use to prepare a bevel edge or quickly remove excess weld reinforcement?
As part of basic preventive maintenance for hand tools, what should be done after identifying a defective tool during inspection?
A welder needs to tighten a loose nut on a jig without damaging its hexagonal head. Which hand tool is most appropriate?
Which measuring instrument is specifically designed to check the size of a weld bead or fillet weld leg length?
Measuring Instruments
What is the purpose of a try square in a welding or fabrication workshop?
Which instrument would a welder use to accurately measure the angle of a bevel-prepared plate edge before welding?
Before storing measuring instruments at the end of a shift, what routine maintenance step helps prevent rust on steel measuring tools?
A welder must check the internal bore diameter of a pipe and record the measurement per workplace procedure. Which sequence best matches correct measuring-instrument practice?
In oxy-acetylene cutting, what is the primary purpose of the cutting torch's preheat flames surrounding the central oxygen jet?
Oxy Acetylene Cutting
Which safety device is fitted to oxy-acetylene equipment to help prevent a flashback from reaching the gas cylinder?
When setting up oxy-acetylene cutting equipment, how is the correct cutting nozzle typically selected?
What is a 'backfire' in oxy-acetylene work, as distinguished from a flashback?
According to standard cutting procedure, what must be done to the oxygen and acetylene gas supply immediately after a cut is completed?
Which type of cut, among straight, bevel, circular and zigzag, would be used to prepare a groove-weld edge with an angled face for a butt joint?
A welder is oxy-acetylene cutting a mild steel plate near the upper thickness limit specified for manual cutting (up to 8 mm). Compared with cutting a thinner 3 mm plate, what adjustment is most likely needed?
In gas welding and brazing, what is 'flux' used for?
Gas Welding And Brazing
Which filler metal is commonly used for brazing, alongside mild steel filler used for gas welding?
Loading more…