According to Ohm's Law, what is the electric current (I) flowing through a heating element with a resistance of 44 ohms when connected to a 220 V AC supply?
Trade Theory And Workshop
Question · Easy
Never enter a tank before testing the air
Short
A single-phase step-down transformer has 1,200 turns in the primary winding and 120 turns in the secondary winding. If the primary voltage is 240 V, what is the secondary output voltage?
Question · Medium
What is the standard frequency of the single-phase alternating current (AC) domestic power supply distributed in Bangladesh by BPDB/DESCO?
What is the primary safety function of connecting equipment earthing (grounding) to the metallic frame of domestic and workshop appliances?
Which electrical protective device is specifically engineered to detect minute earth leakage currents (e.g., 30 mA) and rapidly trip to protect humans from fatal electrocution?
OSHA noise limits
In a residential staircase wiring circuit where a single lamp must be controlled independently from two different locations, which type of switches must be installed?
An electric immersion water heater rated at 1,500 W operates continuously for 4 hours. How much electrical energy does it consume in kilowatt-hours (kWh / units)?
In surface PVC conduit electrical wiring installations, what is the maximum standard spacing permitted between conduit saddles (clips) along straight horizontal runs?
Question · Hard
Which major component of an engine center lathe is mounted on the right end of the bedways and is used to support long workpieces with a center or hold drill chucks?
100 metronomes and 1 rescuer
Which lathe machining operation produces a flat, perpendicular surface on the end face of a cylindrical workpiece?
When mounting a hand hacksaw blade into the frame for general metal cutting, in which direction should the teeth point?
Which grade of hand file has the coarsest tooth spacing and is used for rapid removal of large amounts of excess metal during rough bench fitting?
In a standard three-piece hand tap set used for cutting internal screw threads in a blind hole, which tap has the least chamfer angle (only 1 to 2 threads chamfered) to complete threads to the bottom?
What is the standard point (lip) angle of a general-purpose high-speed steel (HSS) twist drill bit used for drilling mild steel in a fitting workshop?
What is the primary difference in point angle and application between a center punch and a prick (dot) punch?
In oxy-acetylene welding, which type of flame has an equal volume ratio of oxygen and acetylene (1:1) and is used for welding mild steel?
In Manual Metal Arc Welding (MMAW / SMAW), what is the vital role of the chemical flux coating surrounding the electrode core wire?
What is the primary difference between Tungsten Inert Gas (TIG / GTAW) welding and Metal Inert Gas (MIG / GMAW) welding?
Which compound in Ordinary Portland Cement (OPC) is primarily responsible for the development of early strength (within the first 7 days) during hydration?
In civil building construction in Bangladesh, what do the volumetric proportions 1 : 2 : 4 represent in a standard nominal concrete mix?
What is the primary engineering property of fresh concrete measured on-site using the standard Abrams Slump Cone apparatus?
According to Abrams' Law of concrete technology, how does increasing the water-cement (W/C) ratio beyond the optimum requirement affect the compressive strength of hardened concrete?
Which brick masonry bond consists of alternate courses of stretchers and headers, and is considered the strongest bond for load-bearing brick walls?
What is the standard traditional nominal dimensions of a common clay building brick in Bangladesh (excluding mortar joint)?
What is the minimum recommended moist curing period for Ordinary Portland Cement (OPC) concrete structures under normal weather conditions to achieve proper design strength?
Which plumbing fitting is installed below sanitary drainage fixtures (such as washbasins and water closets) to retain a water seal that blocks toxic sewer gases from entering living spaces?
Which plastic piping material is joined using thermal heat fusion welding and is widely specified for hot and cold pressurized domestic water supply in modern buildings?
What is the primary electrical characteristic of an ideal semiconductor PN junction diode when operating under forward-biased versus reverse-biased conditions?
How many semiconductor diodes are required to construct a standard single-phase full-wave bridge rectifier circuit without requiring a center-tapped transformer?
In a desktop computer system unit, what is the primary electrical role of the Switched-Mode Power Supply (SMPS)?
What is the primary physiological mechanism by which an electric shock of 50 mA to 100 mA AC through the human chest causes fatal injury?
Industrial Safety And Measurement
Which Personal Protective Equipment (PPE) is mandatory to protect against falling objects, overhead structural hazards, and head impacts in an industrial workshop?
Why is an electric arc welder required to wear a welding helmet equipped with a specialized optical filter glass (Shade 10 to 12) during manual arc welding?
At or above what continuous eight-hour time-weighted average noise level must hearing protection (earmuffs or earplugs) be provided to industrial workers?
Which safety feature in industrial safety boots protects the technician's feet from crushing injuries caused by dropped heavy metal bars or machinery parts?
When spray-painting metal parts with solvent-based polyurethane paints, which type of respiratory protective equipment is required?
What is the primary operational objective of the Lockout/Tagout (LOTO) safety procedure during maintenance of machinery in a vocational workshop?
Before entering a confined space (such as a deep storage tank, underground utility manhole, or trench), what is the safe atmospheric oxygen concentration range required for entry without breathing apparatus?
What are the three essential components that form the traditional 'Fire Triangle' required for combustion to initiate and continue?
Which class of fire involves ordinary solid combustible materials such as wood, paper, textiles, rubber, and trash?
Which fire extinguishing agent should NEVER be applied to a Class B fire involving burning petrol, kerosene, or diesel fuel?
Which type of fire extinguisher is best suited for an electrical fire inside a computerized control panel because it leaves no electrically conductive or corrosive residue?
Which specialized extinguishing agent must be deployed to safely extinguish a Class D combustible metal fire involving burning magnesium chips or titanium swarf?
What does the standardized fire safety acronym 'PASS' stand for when operating a portable fire extinguisher?
What is the immediate, correct first-aid action for a workshop technician who suffers a second-degree thermal burn on the forearm from a hot welded workpiece?
Loading more…