BCSP ASP

A storage tank is 30 feet in diameter and 40 feet high. What is the maximum volume of liquid it can hold in cubic feet?

• A28,274 cubic feet
• B37,699 cubic feet
• C56,549 cubic feet
• D113,097 cubic feet

A lifting operation requires moving a 5,000-pound load. If the rigging is configured with a 4-leg bridle hitch at a 60 deg angle from horizontal, what is the load on each leg?

• A1,250 pounds
• B1,443 pounds
• C1,667 pounds
• D2,500 pounds

An employee is exposed to noise at 92 dBA for 3 hours and 85 dBA for 5 hours during an 8-hour shift. Using OSHA's formula, does this exceed the OSHA PEL of 90 dBA as an 8-hour TWA?

• ANo, the TWA is about 88.5 dBA
• BNo, the TWA is about 89.7 dBA
• CYes, the TWA is about 90.5 dBA
• DYes, the TWA is about 93.8 dBA

A company had 3 recordable injuries last year with 250,000 total hours worked. What is the Total Recordable Incident Rate (TRIR)?

• A1.2
• B2.4
• C3.6
• D4.8

A worker lifts a box from the floor to a shelf 48 inches high. The box weighs 40 pounds and is held 20 inches from the body at the destination. Using simplified NIOSH lifting equation principles, which factor contributes MOST to increased risk?

• AThe vertical height of the lift
• BThe horizontal distance from the body
• CThe weight of the object
• DThe frequency of lifting

Which international standard provides a framework for occupational health and safety management systems?

• AISO 9001
• BISO 14001
• CISO 45001
• DANSI Z10

According to the hierarchy of controls, which control method is MOST effective at reducing risk?

• AEngineering controls
• BAdministrative controls
• CPersonal protective equipment (PPE)
• DElimination/substitution

During a Job Hazard Analysis (JHA), which approach should be used to prioritize which jobs to analyze first?

• AAnalyze jobs alphabetically for consistency
• BFocus on jobs with highest frequency of injuries or near-misses
• CStart with the newest jobs and work backward
• DPrioritize based on employee seniority

In a Failure Mode and Effects Analysis (FMEA), what does the Risk Priority Number (RPN) represent?

• AThe probability of an accident occurring
• BSeverity x Probability x Detection
• CThe cost of implementing controls
• DThe number of identified hazards

What is the primary purpose of a fault tree analysis?

• ATo track employee training completion
• BTo identify combinations of events that could lead to a specific undesired event
• CTo calculate workers compensation premiums
• DTo document OSHA compliance inspections

A facility needs to control hazardous energy during equipment maintenance. Which OSHA standard specifically addresses this requirement?

• A29 CFR 1910.95 (Occupational Noise Exposure)
• B29 CFR 1910.147 (The Control of Hazardous Energy/Lockout/Tagout)
• C29 CFR 1910.1200 (Hazard Communication)
• D29 CFR 1910.134 (Respiratory Protection)

Which type of machine guard is generally considered the MOST reliable because it does not depend on worker behavior?

• AInterlocked guards
• BSelf-adjusting guards
• CFixed barrier guards
• DPull-back devices

A trench is being excavated in stable rock to a depth of 12 feet. What protective system is required?

• ANo protective system is required in stable rock
• BSloping or benching is required
• CA trench box or shield is required
• DShoring or trench box is required unless the excavation is entirely in stable rock

What is the primary purpose of the Globally Harmonized System (GHS) of Classification and Labeling of Chemicals?

• ATo eliminate the need for Safety Data Sheets
• BTo standardize chemical hazard classification and communication worldwide
• CTo ban the use of hazardous chemicals
• DTo create different standards for each country

In incident investigation, what technique involves repeatedly asking "Why?" to identify root causes?

• AFault Tree Analysis
• B5 Whys technique
• CEvent Tree Analysis
• DBow-tie analysis