What is the main purpose of GD&T on an engineering drawing?
Asme Gdtp Scope
Question · Easy
ASME describes the GDTP Technologist level as primarily measuring a candidate's ability to:
Chapter 1: Scope, Certification Logistics, Fundamental Rules & General Dimensioning
1.1 ASME GDTP Technologist Exam Scope, Prometric Logistics, & Certification Rules
Study guide
Which statement matches the official ASME Y14.5-2009 Technologist exam format published by ASME?
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
For the ASME Y14.5-2009 Technologist exam, what overall passing score does ASME publish?
Question · Medium
In the official Y14.5-2009 Technologist distribution, which category has the largest approximate share of exam questions?
Why should a candidate pay attention to whether an exam or drawing is based on Y14.5-1994 or Y14.5-2009?
1.2 Fundamental Rules of ASME Y14.5-2009 (Rules a through p)
Which candidate profile best fits ASME's published audience for GDTP Technologist certification?
A drawing uses basic dimensions from datums to locate a hole pattern. What does that signal to the Technologist candidate?
What certification validity period does ASME publish for GDTP certificates?
After ASME accepts a GDTP application, what scheduling window does the official page describe?
1.3 Engineering Drawing Standards, Drawing Units, & Basic vs. Toleranced Dimensions
What is a basic dimension used for in GD&T?
Asme Gdtp General Tolerancing
A width is specified as 25.00 +/- 0.10. What are the size limits?
Under the common Y14.5 envelope principle for a regular feature of size, what is required at MMC?
Which statement best describes RFS when no material condition modifier is shown in a feature control frame?
1.4 Dimensioning Features: Diameters, Radii, Chamfers, Countersinks, Counterbores, Spotfaces, Keyseats & Slots
A drawing locates a hole with rectangular coordinate dimensions but no geometric tolerance or datum reference frame. What is the main weakness compared with a position control?
Which drawing element normally supplies the allowable variation for a basic 50.00 location dimension?
A hole size is specified as 10.0 to 10.2. For this internal feature of size, what is its MMC?
A pin size is specified as 9.8 to 10.0. For this external feature of size, what is its MMC?
1.5 Application of Dimensions & Location of Features: Lines, Leaders, Reference Dimensions, Rectangular vs. Polar Coordinates
A drawing note says dimensions are in millimeters unless otherwise specified. Which interpretation is normally correct for a geometric tolerance value of 0.20 on that drawing?
A rectangular tab must always fit into a mating slot at its maximum material size. Which general tolerancing concept is most directly being protected?
Question · Hard
Which geometric characteristic is a form control?
Asme Gdtp Symbology
Which control is normally used to locate the axis of a hole pattern from datums?
Chapter 2: Features, Limits of Size, & Material Condition Principles
2.1 Features, Features of Size, & Limits of Size
In a feature control frame, what does the diameter symbol before a position tolerance value usually indicate?
What does an MMC modifier attached to a geometric tolerance communicate?
Which pairing of control type and example is correct?
What is the difference between a datum feature and a datum?
Asme Gdtp Datum Referencing
2.2 Rule #1 (Taylor Principle / Envelope Rule), Its Exceptions & Overrides
For a prismatic part resting on a primary planar datum feature A, what does that primary plane typically establish first?
In the common 3-2-1 datum setup using three mutually perpendicular planes, what does the tertiary datum usually do?
Why does the order of datum references in a feature control frame matter?
When are datum targets especially useful?
2.3 Material Condition Concepts: MMC, LMC, & RFS Calculations
A hole is identified as datum feature B and referenced at MMB. What may occur if the actual hole is larger than its maximum material boundary size?
What is a datum feature simulator?
A datum feature symbol containing the letter A is attached to a mounting face. What does the letter A identify?
A feature control frame references datums A|B|C. In ordinary interpretation, which datum has precedence?
Chapter 3: General Tolerancing & Symbology
3.1 Direct Tolerancing, Limit Dimensioning, & Angular Tolerancing
A cylindrical boss is used as datum feature B. What kind of datum is commonly established from that feature?
A datum feature of size is referenced without a material boundary modifier. What is the normal implication?
Which statement best distinguishes bonus tolerance from datum shift?
A part has a wide base surface A and two perpendicular side faces B and C. Why might changing a control from A|B|C to A|C|B matter?
Loading more…