ASTM D4541 pull-off adhesion testing requires reporting both the numerical result and:
Advanced Inspection Methods
Question · Medium
Why must a CIP Level 2 inspector treat a bulging or kinked abrasive-blast supply hose as an immediate stop-work hazard?
Safety
Flashcard
When performing an ASTM D4541 pull-off test on a thin-film coating (< 10 mils), scoring (cutting a groove) around the dolly is:
Question · Hard
ICRI number used to specify the roughness of a prepared substrate; the 2013 guideline added a tenth level for repair work.
Surface preparation
Guess the Term
Introduction & Exam Overview
CIP Level 2 Exam Facts and Format
Study guide
Cheat sheet
A Type IV portable pull-off adhesion tester is:
Read the clue and guess the term in 6 tries.
Game
What does it mean for inspection equipment to be 'intrinsically safe,' and when must a CIP Level 2 inspector confirm it?
The ASTM D3359 Method B (cross-cut lattice) test is suitable for coatings up to approximately:
___ scale: removed from steel together with rust by pickling before hot-dip galvanizing.
ASTM D5402 solvent rub testing for inorganic zinc silicate primers typically uses:
What are the essential components of an Inspection and Test Plan (ITP)?
Inspection Process
The method of evaluating coating hardness by drawing successive pencil leads of known hardness across the film until one cuts or scratches it is:
To treat stainless steel in an acid bath to remove scale before passivation.
Prerequisites, Certification Path, and Renewal
Chlorides on a previously coated surface during overcoat preparation should be tested by:
Swap tiles to line up three of the same term.
Term Match
How does a de facto standard differ from a national or international standard referenced in a coating specification?
Infrared thermography of an operating tank with applied coatings can be used to detect:
Coating measurement taken with a magnetic or eddy-current gauge after the coating has set.
Coating inspection
Ultrasonic thickness (UT) measurement of a steel substrate under a coating is primarily used to:
Nde Familiarity
Why does the CIP Level 2 certification carry authority to review and verify a CIP Level 1 inspector's work, rather than each level operating independently?
Before performing an adhesion test on a critical coating system, the inspector should:
Question · Easy
Measurement taken with a notched or comb gauge immediately after application, before the coating cures.
July 2026 Blueprint and Study Strategy
When using a Type 2 electronic DFT gauge over a very rough profile (e.g., 4-5 mil profile), the measured coating thickness should be:
Flip two cards at a time to find matching terms.
Term Pairs
What does it mean to 'verify CIP Level 1 work in a shop environment'?
Elcometer, DeFelsko, and Fischer are common manufacturers of:
___ gauge: trademarked instrument with a 50-power microscope that cuts a V-groove to measure total coating thickness and individual coats.
Destructive adhesion testing creates a discrete test wound. The inspector should:
Why must a CIP Level 2 inspector be able to justify the purpose and cost of an inspection activity to a client?
The ISO 4628 series is used to evaluate:
Periodic on-site check used to verify inspection results when oversight is mostly remote.
Inspection process
Process Safety: Equipment and Job-Site Hazards
Cathodic disbondment (CD) testing of pipeline coatings is performed per:
Pipeline Coatings
Find five hidden terms in a grid of letters.
Term Search
What does the CIP Level 2 target-audience description say a Certified Coatings Inspector typically inspects that goes beyond routine steel coating work?
For inspection of a complex tank interior, the inspector's standard test for DFT involves:
Project attribute graded moderate or critical that decides whether a Level 2 inspector needs direct oversight by a Level 3.
Which of the following is an example of a destructive inspection method on a completed coating?
What role does the written job specification play during inspection planning?
Why is it important to test for amine blush on new epoxy coatings?
Coating Failures
Plant-applied external pipe coating supplied as a powder.
Coatings and application
Loading more…