Which ACI document is the mandatory specification that the Shotcrete Inspector uses to enforce project requirements for wet-mix and dry-mix shotcrete?
Aci 506 Specification
Question · Easy
Under IBC Chapter 17, who is responsible for submitting the statement of special inspections for a structural shotcrete project?
Ibc Chapter 17
Question · Medium
Which of the following is the PRIMARY difference between wet-mix and dry-mix shotcrete that affects inspection focus?
Shotcrete Processes
Trades Exam Prep Podcast
Listen on Spotify
Podcast
According to ASTM C1140, what is the MINIMUM recommended size for a shotcrete test panel?
Test Panels
What is the minimum thickness of a shotcrete test panel per ASTM C1140?
Who should shoot the preconstruction and quality-control test panels on a shotcrete project?
Which ACI document is the Guide to Shotcrete (non-mandatory), providing background on materials, equipment, and procedures for both wet-mix and dry-mix?
Aci 506 Documents
According to ACI 506R, how does rebound generally compare between wet-mix and dry-mix shotcrete?
According to ACI 506R, coarse-aggregate shotcrete with more than what percentage of coarse aggregate exhibits noticeably higher rebound for both wet-mix and dry-mix?
Question · Hard
Under IBC Chapter 17, special inspection of structural shotcrete placement is generally classified as what type of inspection?
Which ACI certification is required for nozzlemen placing structural shotcrete, and which document governs the craftsman workbook?
Nozzleman Qualification
A nozzleman holds current ACI Shotcrete Nozzleman certification for vertical wet-mix placement. The project calls for overhead dry-mix placement. What should the inspector do?
What is the primary purpose of a preconstruction shotcrete mockup per ACI 506.2?
Preconstruction
During shotcrete placement, the inspector observes the nozzleman holding the nozzle at a severe angle (approximately 30 degrees) to the surface near rebar. What is the MOST LIKELY consequence the inspector should be concerned about?
Placement
According to ACI 506R, what is the typical recommended nozzle-to-surface distance for optimal shotcrete placement?
Which of the following is a critical defect that the Shotcrete Inspector must ensure does NOT remain in the finished structural shotcrete?
Defects
Per ACI 506.2, rebound material that has fallen during shooting:
Per ACI 506.4R and industry practice, shotcrete cores for compressive strength testing are typically obtained per which ASTM standard?
Evaluation
A shotcrete test panel is cut into quarters for visual examination. The inspector observes a thin, continuous horizontal plane of sand and rebound material midway through the thickness. This is MOST LIKELY:
In wet-mix shotcrete, which fresh-property test is typically performed by the inspector or testing technician to verify consistency before placement?
Mix Verification
Why is a conventional slump test NOT used to verify dry-mix shotcrete consistency?
Which ACI document is the Guide to Shotcrete for the Repair of Concrete Structures?
Which ACI document provides guidance specifically for underground shotcrete applications such as tunnel linings?
Before any structural shotcrete is placed, the inspector should verify which of the following reinforcement conditions?
Pre Shooting Inspection
Per ACI 506R, how should reinforcing bar clearances be sized relative to the maximum aggregate dimension in shotcrete?
Which of the following is NOT typically a duty of the ACI Shotcrete Inspector during a project?
Inspector Duties
What is the minimum required acceptable compressive strength determination for shotcrete cores specified by many projects per ASTM C42?
Acceptance Criteria
During dry-mix shotcrete placement, the inspector notices the nozzleman repeatedly adjusts the water valve at the nozzle. What is the inspector's concern?
Which of the following air-supply conditions is MOST LIKELY to cause poor compaction in dry-mix shotcrete?
Equipment
According to ACI 506.2, what is generally the FIRST step the nozzleman and inspector take when shooting begins on a new area containing reinforcement?
What is the purpose of a gunwire or depth gauge in shotcrete placement, and what should the inspector verify about it?
According to ACI 506R, during the shooting of wet-mix shotcrete, the inspector should confirm the delivery time from batching to placement does not exceed:
Which type of defect is MOST commonly found directly behind reinforcing bars when shooting technique is poor?
For cold-weather shotcrete placement, what is generally the minimum temperature of the shotcrete as placed per ACI 506.2 and cold weather practice?
Curing Protection
Per ACI 506.2 and ACI 308, what is the minimum recommended moist-curing period for shotcrete after placement?
In evaluating shotcrete cores per ACI 506.4R, which of the following visual characteristics should be noted and reported by the inspector?
What is the role of accelerators in shotcrete (particularly for overhead and underground applications), and what inspection concern do they raise?
The inspector observes sloughing (sagging) of freshly placed shotcrete on a vertical wall. What is the MOST LIKELY cause?
Under IBC Chapter 17, when the special inspector observes a discrepancy or nonconforming work, what is the proper procedure?
When does the cutting of cores from test panels typically take place per ASTM C1140?
ACI 506.2 requires that shotcrete mixture proportions be established by which method(s)?
What is the primary reason for limiting maximum aggregate size in shotcrete compared to conventional concrete?
Materials
When a nozzleman stops placement mid-lift and returns later, what inspection concern arises?
What are the typical nozzle orientations for which an ACI Shotcrete Nozzleman must be separately qualified?
Per ACI 506.2, what is typically the minimum compressive strength for structural shotcrete unless otherwise specified?
Which ACI document is the formal Evaluation of Shotcrete guide that the inspector relies on for coring and examination procedures?
The inspector must verify that test panels are cured in what manner per ASTM C1140?
Loading more…