Which construction activities fall within the scope of a Florida Certified Structural Masonry Specialty Contractor?
Fundamentals
Question · Easy
How deep before you need a trench box?
Short
A candidate seeking Florida structural masonry certification must pass which set of examinations?
What is the minimum experience generally required to qualify for the Florida Structural Masonry Specialty Contractor license?
Question · Medium
Trades Exam Prep Podcast
Listen on Spotify
Podcast
What are the administration details of the Florida Structural Masonry Trade Knowledge examination?
Which ASTM C270 mortar type has the highest minimum compressive strength and is used for below-grade, heavy-load masonry?
Materials Science
What are the nominal dimensions of a standard full-length concrete masonry unit used in structural walls?
What distinguishes masonry cement from Portland cement as a mortar ingredient?
Which ASTM standard governs load-bearing concrete masonry units?
How is coarse masonry grout distinguished from fine grout under ASTM C476?
What minimum compressive strength must masonry grout meet at 28 days per TMS 602 and ASTM C476?
In hot-weather masonry construction, what is the primary purpose of adding a retarding admixture to mortar?
Which ASTM brick weathering grade is recommended for severe exposure where freezing of saturated brick is likely?
How does sand gradation most directly affect field mortar performance?
Question · Hard
What does the designation Grade 60 refer to for reinforcing bars used in masonry and concrete?
Which Portland cement type is specified when moderate sulfate resistance is needed, such as in some below-grade applications?
Why is masonry grout mixed to a much higher slump (8 to 11 in) than structural concrete?
Using the estimator's rule that one 80-lb bag of Type S mortar lays about 8 blocks, approximately how many bags are needed for a 200 sq ft single-wythe CMU wall (before waste)?
What is the purpose of a form release agent applied to form surfaces before placing concrete?
Formwork
What function do form ties serve in wall formwork?
What is the purpose of reshoring after stripping slab or beam formwork?
Side forms for non-load-bearing members may generally be removed when the concrete has reached what condition?
Why is camber built into formwork for long-span beams and slabs?
Which document establishes the tolerances for concrete construction and formwork dimensions?
Formwork for tall walls must be braced laterally primarily to resist what load?
What does the plyform designation B-B Class I indicate?
Which factors most influence the lateral pressure that fresh concrete exerts on wall forms?
Which form tie is designed to be withdrawn from the concrete after the forms are stripped, leaving only a small conical patch?
Why are chamfer strips placed at the corners of formwork?
What is the purpose of a keyway formed at a construction joint in a footing or slab?
A reinforced concrete wall is 10 ft high and 40 ft long. What is the total form contact area required for both faces?
How many 4 ft x 8 ft sheets of plyform are needed to sheath one face of a 10 ft high by 40 ft long wall, using full sheets only?
In cold-weather concreting, why is formwork and fresh concrete often insulated?
What is the purpose of cleanout openings at the bottom of high-lift grouted masonry wall assemblies?
A reinforced CMU wall calls for one #5 vertical bar in each grouted cell. What are the nominal diameter and cross-sectional area of that bar?
Reinforcing Steel
What is the function of bolsters (chairs) placed under reinforcing bars in formwork?
Why are reinforcing bars tied together with wire at intersections?
Per ACI 318, what is the minimum concrete cover for a #5 bar in a wall cast in removable forms that will NOT be exposed to weather or in contact with ground?
What is the minimum concrete cover for a #6 reinforcing bar cast against and permanently exposed to earth?
Which factors directly influence the required lap splice length for reinforcing bars?
What is the purpose of a standard 90-degree or 180-degree hook at the end of a reinforcing bar?
When are mechanical splices typically specified in preference to lap splices?
What precaution is required when handling and placing epoxy-coated reinforcing bars?
Per ACI 117 and CRSI practice, what is a typical tolerance for the position of reinforcing bars in walls and slabs unless the engineer specifies otherwise?
What role do stirrups play in a reinforced concrete beam?
What is the purpose of dowels extending from a footing into a concrete or masonry wall?
A 20 ft long CMU wall is reinforced with #5 vertical bars spaced 24 in on center, including one bar at each end. How many vertical bars are required?
Loading more…