According to the International Residential Code (IRC R502.8), what is the maximum allowable notch depth at the end of a solid sawn floor joist?
Rough Carpentry Framing
Question · Medium
Six feet: a hard-hat anthem
Short
What is the minimum required distance between the edge of a bored hole and the top or bottom edge of a solid sawn floor joist per IRC R502.8?
Question · Easy
In a load-bearing exterior wood stud wall, what is the maximum allowable diameter of a bored hole in a single stud without requiring a protective shoe or double stud configuration?
Trades Exam Prep Podcast
Listen on Spotify
Podcast
What is the maximum notch depth permitted in a non-bearing wood wall stud according to IRC R602.6?
When a double top plate in a load-bearing wall is notched or drilled more than 50% of its width for plumbing pipes, what code-compliant reinforcement must be installed?
Question · Hard
OSHA fall heights, to scale
What is the maximum allowable live load deflection for a floor joist supporting a finished plaster ceiling per the International Building Code (IBC Table 1604.3)?
Calculate the total board feet contained in ten 2x8 nominal lumber boards, each 16 feet in length.
How many board feet of lumber are in five 4x12 timbers that are each 20 feet long?
According to IRC R602.7, how many jack studs (trimmers) are required under each end of an exterior wall header supporting a clear span of 7 feet in a 28-foot wide building under standard roof loads?
Unless engineered calculations are provided, what is the maximum allowable cantilever length for 2x10 wood floor joists supporting an exterior bearing wall per IRC R502.3.3?
Which wood plate member MUST be preservative-treated or naturally durable wood according to IRC R317.1?
What is the minimum required lap offset distance for joints in double top plates per IRC R602.3.2?
When installing subfloor wood structural panels (such as 3/4-inch OSB or plywood) over floor joists, what gap should be left between panel end and edge joints to allow for expansion?
In wood-frame wall construction, what is the maximum vertical distance between horizontal fireblocking lines in concealed stud spaces per IRC R302.11?
Which of the following is an approved material for fireblocking concealed draft spaces according to IRC R302.11.1?
What is the minimum clearance required between an untreated wood post/column supporting a deck or floor beam and exposed earth per IRC R317.1?
What is the minimum distance required between the bottom of untreated wood floor joists and exposed ground in an under-floor crawl space?
Estimate the minimum number of studs required to frame a straight 48-foot wall laid out at 16 inches on center, including 3 extra studs for corners and partitions.
When framing wood stud walls over 10 feet tall, horizontal fireblocking or mid-height bridging must be placed so that no unblocked vertical space exceeds what distance?
Which modification is STRICTLY PROHIBITED when installing pre-engineered I-joists (TJI joists)?
When cutting holes in the OSB web of an I-joist for ductwork or piping, where should the largest holes be located for optimal structural performance?
When installing glued-laminated timber (glulam) beams, how should the manufacturer's factory camber mark be oriented during installation?
Under IRC R502.7.1, solid sawn floor joists exceeding what nominal size must be supported laterally by solid blocking, bridging, or a continuous 1x3 strip at intervals not exceeding 8 feet?
What is the minimum end bearing length required for wood floor joists supported on wood or metal framing members per IRC R502.6?
What is the minimum required end bearing length when floor joists bear directly on concrete or masonry foundation walls per IRC R502.6?
In advanced framing (Energy Efficient Framing), what is the primary structural advantage of constructing a two-stud corner (California Corner) with drywall clips or backup backing?
What is the minimum angle relative to horizontal required for a traditional 1x4 wood let-in corner brace per IRC R602.10.6?
Under American Softwood Lumber Standards (PS 20), lumber stamped 'S-DRY' has been dried to a maximum moisture content of what percentage at the time of surfacing?
A roof design has a total span of 24 feet and a total rise of 6 feet. What is the roof pitch?
Calculate the line length of a common rafter (before ridge deduction) for a roof with a run of 12 feet and a rise of 5 feet.
According to BCSI-1 (Building Component Safety Information) standards, what is the primary purpose of temporary Continuous Lateral Restraint (CLR) installed on wood truss webs?
Roof Systems Trusses
When hoisting pre-engineered wood roof trusses with spans exceeding 60 feet, what hoisting equipment is mandatory per BCSI-B1 guidelines?
If a jobsite carpenter needs to cut a web member of a pre-engineered wood truss to accommodate an HVAC duct, what action is required by code?
According to IRC R802.4.2, what is the minimum required thickness and depth of a ridge board supporting opposing roof rafters?
What is the primary structural function of collar ties (installed in the upper third of attic rafter framing) per IRC R802.4.6?
In standard equal-pitch hip roof framing (12 inches of run per foot), what is the horizontal run per foot of a hip or valley rafter?
When installing 7/16-inch OSB roof sheathing over rafters spaced 24 inches on center, panel edge clips (H-clips) are used primarily to:
Calculate the minimum net free ventilating area (NFVA) required for an enclosed attic space measuring 40 feet by 30 feet, assuming the standard 1/150 ventilation ratio under IRC R806.1.
According to IRC R806.3, what minimum clearance must be maintained between roof insulation and roof sheathing at the eave soffit vents to ensure unobstructed airflow?
When framing gable end overhangs (fly rafters) extending more than 12 inches beyond the gable wall, how far back into the interior roof framing must lookout members extend?
Permanent web diagonal bracing on wood trusses is designed to remain in place primarily to perform which function?
A roof rafter has a total run of 16 feet and a pitch of 8:12. What is the total rise of the rafter?
Heavy multi-ply girder trusses carrying load from incoming jack trusses generally require which specialized connection hardware?
According to IRC R802.4.5, roof purlins used to reduce rafter spans must be supported by continuous struts extending down to bearing walls at an angle not less than:
When framing a roof opening for a chimney or dormer that cuts through more than two rafters, what header and trimmer configuration is required per IRC R802.9?
Loading more…