Alabama Metal Building Erection Contractor Examination Feed

Question

Before steel erection of a metal building begins, the controlling contractor must provide written notification that the concrete in footings, piers, and walls has attained adequate strength and that:

Sitework

Question · Medium

Question

For systems-engineered metal buildings, each structural column must be anchored by a minimum of how many anchor rods (anchor bolts)?

Anchor Bolts Layout

Question · Medium

Question

The metal building manufacturer's anchor bolt plan is primarily used to:

Anchor Bolts Layout

Question · Easy

Podcast

Trades Exam Prep Podcast

Listen on Spotify

Podcast

Question

If an embedded anchor rod is found bent or damaged after concrete placement, the correct action is to:

Anchor Bolts Layout

Question · Medium

Question

When setting anchor rods with a template before a concrete pour, the template should be:

Anchor Bolts Layout

Question · Medium

Question

Site grading under a metal building foundation should provide positive drainage away from the building primarily to:

Sitework

Question · Medium

Question

On metal building erection drawings, the building's overall length is typically measured:

Anchor Bolts Layout

Question · Medium

Question

Before excavation for metal building foundations, the contractor should:

Sitework

Question · Medium

Question

Cold joints in foundation concrete should be avoided or properly prepared because they:

Concrete

Question · Medium

Question

The specified compressive strength (f'c) of concrete for metal building foundations is typically verified by:

Concrete

Question · Medium

Question

Adding water to a ready-mixed concrete truck on site without authorization is discouraged primarily because it:

Concrete

Question · Hard

Question

For a metal building slab-on-grade, control joints are used primarily to:

Concrete

Question · Medium

Question

Proper concrete curing after placement is important because it:

Concrete

Question · Easy

Question

When placing concrete for piers that receive metal building columns, the top surface should be:

Concrete

Question · Medium

Question

Segregation of concrete during placement is most likely when:

Concrete

Question · Medium

Question

Non-shrink grout under a metal building column base plate is typically used to:

Concrete

Question · Medium

Question

Air-entrained concrete is specified for many exterior foundations primarily to improve:

Concrete

Question · Medium

Question

If foundation concrete is placed in hot weather, which practice best protects quality?

Concrete

Question · Hard

Question

Formwork for metal building foundations must be designed and constructed to resist:

Concrete Formwork

Question · Medium

Question

Form release agent should be applied so that it:

Concrete Formwork

Question · Medium

Question

When formwork is not plumb and true before a pier pour, the most likely result is:

Concrete Formwork

Question · Easy

Question

Ties and spreaders in foundation wall forms are used to:

Concrete Formwork

Question · Medium

Question

Forms should remain in place until concrete has gained enough strength to:

Concrete Formwork

Question · Medium

Question

Chamfer strips at outside corners of formed concrete are used mainly to:

Concrete Formwork

Question · Easy

Question

Rate of concrete placement into tall forms should be controlled because rapid filling can:

Concrete Formwork

Question · Hard

Question

Before placing concrete, formwork should be inspected for:

Concrete Formwork

Question · Easy

Question

Earth forms (trench forms) for continuous footings may be acceptable when soil is stable, but they require:

Concrete Formwork

Question · Medium

Question

Formwork bracing for free-standing pier forms must resist:

Concrete Formwork

Question · Medium

Question

Clear cover over reinforcing steel in foundations is provided mainly to:

Concrete Reinforcement

Question · Easy

Question

Reinforcing bars should be free of loose rust, mill scale, oil, and mud before concrete placement because contaminants can:

Concrete Reinforcement

Question · Easy

Question

Bar supports (chairs, dobies, spacers) are used to:

Concrete Reinforcement

Question · Easy

Question

When two reinforcing bars are lapped for continuity, the lap length must be:

Concrete Reinforcement

Question · Medium

Question

Dowels projecting from a footing into a pier or wall are intended to:

Concrete Reinforcement

Question · Medium

Question

Welded wire reinforcement (WWR) in slabs must be positioned:

Concrete Reinforcement

Question · Medium

Question

Hooked ends on reinforcing bars are provided when:

Concrete Reinforcement

Question · Hard

Question

Tying reinforcement at intersections is important so that:

Concrete Reinforcement

Question · Easy

Question

Epoxy-coated reinforcement, when specified for corrosive environments, requires:

Concrete Reinforcement

Question · Medium

Question

If reinforcing steel conflicts with an embedded anchor rod pattern, the erector or foundation crew should:

Concrete Reinforcement

Question · Hard

Question

In metal building work, masonry is most commonly used for:

Masonry

Question · Easy

Question

Mortar for unit masonry should be mixed and used so that:

Masonry

Question · Medium

Question

When a metal building column base is adjacent to a masonry wall, the interface typically requires:

Masonry

Question · Hard

Question

Concrete masonry units (CMU) used in foundation or partial-height walls should be:

Masonry

Question · Easy

Question

Grouted reinforced masonry cells must be filled with grout that:

Masonry

Question · Medium

Question

Weep holes in masonry cavity or veneer walls are provided to:

Masonry

Question · Easy

Question

Control joints in long masonry walls are intended to:

Masonry

Question · Medium

Loading more…