Under the International Building Code (IBC), glazing in which of the following is generally considered a hazardous location requiring safety glazing?
Codes And Safety
Question · Easy
Six feet: a hard-hat anthem
Short
Per IBC glazing-adjacent-to-door rules, safety glazing is typically required when the nearest vertical edge of the glass is within what horizontal distance of a closed door and the bottom of the glass is less than 60 inches above the walking surface?
Which breakage pattern is characteristic of fully tempered glass?
Windows And Glazing
Trades Exam Prep Podcast
Listen on Spotify
Podcast
Laminated safety glass stays in the opening after impact primarily because of which component?
According to NFPA 80, fire door assemblies must generally be inspected at least how often after initial installation?
Doors And Hardware
OSHA fall heights, to scale
A labeled fire door assembly is generally required to do which of the following when released from the open position?
On a National Fenestration Rating Council (NFRC) label, a lower U-factor indicates that the window:
What does the Solar Heat Gain Coefficient (SHGC) on a window primarily describe?
Under OSHA construction fall-protection rules (29 CFR 1926 Subpart M), workers on unprotected sides and edges are generally protected at what height above a lower level?
ADA Standards generally require a minimum clear opening width of how many inches for an accessible door measured with the door open 90 degrees?
For new construction, ADA-accessible door thresholds are generally limited to a maximum height of:
Which CSI MasterFormat division typically covers doors, windows, and glazing?
Installation And Estimating
ANSI/BHMA Grade 1 hardware is best described as:
What is the primary function of a door closer?
An exit device (panic hardware) is primarily intended to:
Low-emissivity (low-e) coatings on glass primarily improve energy performance by:
Filling the air space of an insulating glass unit (IGU) with argon typically:
When storing flat glass on site, the preferred practice is to:
What document on a set of architectural drawings typically lists each door's mark, size, type, material, fire rating, and hardware set?
Safety glazing used in doors and other hazardous locations in the United States is commonly required to meet which federal impact standard?
A solid-core wood door is generally preferred over a hollow-core door in commercial work because it offers:
Hollow metal doors and frames are widely used in commercial buildings primarily because they:
ADA requires operable hardware on accessible doors to be usable:
For interior accessible hinged doors, ADA generally limits opening force to a maximum of approximately:
The rough opening for a window or door unit is typically sized to be:
Flashing around windows and doors is installed primarily to:
Which glass type is generally NOT considered safety glazing for human-impact hazardous locations?
When handling large glass lites, vacuum cups are used primarily to:
A butt hinge is best described as:
Weatherstripping at doors and windows is installed primarily to:
Under IBC 2406.4.3, a window is a hazardous location requiring safety glazing when ALL of the following conditions are met EXCEPT:
Question · Medium
Glazing in walls enclosing bathtubs, showers, and similar wet areas is generally treated as a hazardous location when the bottom edge is less than what height above the standing surface and other proximity criteria are met?
Per NFPA 80 guidance commonly applied to swinging steel fire doors, the clearance between the top/vertical edges of the door and the frame is generally:
Where no sill exists, the maximum clearance under a swinging fire door to the floor is commonly limited by NFPA 80 to:
Why are mechanical hold-open arms generally prohibited on labeled fire doors?
On a pair of fire doors, a coordinator is used to:
Flush bolts on the inactive leaf of a door pair primarily:
A continuous hinge is often specified on high-traffic or heavy doors because it:
In door hardware hand terminology, a left-hand (LH) door is one that:
A cylindrical (bored) lock differs from a mortise lock primarily in that a cylindrical lock:
An electric strike is used to:
In access-control terminology, a fail-safe locking device is designed to:
Magnetic locks (maglocks) on egress doors must generally be installed so that:
Parallel-arm door closer mounting is often selected because it:
On fire-rated doors, vision lites and glazing must:
Loading more…