How many board feet are in one 2×10 that is 16 feet long?
Estimating And Plan Reading
Question · Hard
Six feet: a hard-hat anthem
Short
A wall is 32 feet long and studs are spaced 16 inches on center. How many studs are required for that wall line if you count both end studs and ignore openings?
On a floor plan drawn at a scale of 1/4 inch = 1 foot, a wall measures 3-1/2 inches long on the drawing. What is the actual wall length?
Question · Easy
Trades Exam Prep Podcast
Listen on Spotify
Podcast
Which plan view typically shows door and window rough opening sizes, wall locations, and overall building dimensions for framing layout?
Question · Medium
How many 4×8 sheets of subfloor are needed to cover a rectangular floor area that is 24 feet by 32 feet, with no waste allowance?
OSHA fall heights, to scale
A material takeoff lists twenty 2×4 studs that are each 8 feet long. How many board feet is that order?
On construction drawings, a dashed line that indicates an object above or hidden from the viewing plane is most commonly called a:
A common residential live-load design value used when selecting floor joist spans for typical rooms is:
When reading a detail callout such as "5/A3," what does it most commonly indicate?
A rectangular deck is 12 feet by 16 feet. What is the diagonal length of the deck to the nearest tenth of a foot?
Which document typically governs lumber grade, species, and nailing schedules when they are not fully dimensioned on the architectural floor plan?
If exterior wall sheathing costs $28 per 4×8 sheet and a takeoff shows 48 sheets needed, what is the sheathing material cost before tax?
A building section drawing is most useful to a framer for determining:
What is the primary purpose of a lumber takeoff before ordering materials?
An exterior wall is 9 feet high and 40 feet long. Ignoring openings, about how many square feet of wall sheathing are needed for one side of that wall?
When squaring a foundation or floor platform using the 3-4-5 method, a triangle with sides of 9 feet, 12 feet, and what hypotenuse confirms a right angle?
Layout
What is the main purpose of batter boards at the start of building layout?
A rectangular foundation measures 28 feet by 40 feet. What should the corner-to-corner diagonal measure if the foundation is square?
When laying out stud locations on a sole plate for 16-inch on-center spacing, where is the first regular stud mark typically placed after the end stud?
What tool is commonly used to transfer level elevations around a site for foundation and plate layout?
When checking a wall for plumb, the carpenter is verifying that the wall is:
What is the purpose of a story pole in carpentry layout?
Rough openings for doors and windows are laid out larger than the unit size primarily to:
If joists are laid out 16 inches on center starting with a joist at zero, the layout mark for the joist centered at 8 feet falls at how many inches from the start?
When laying out a partition that intersects a long wall, the intersecting wall should be located from the plans by measuring:
A chalk line is most appropriately used during framing layout to:
Before standing walls, the sole plate is often temporarily fastened to the subfloor or deck. What is the primary reason?
In modern residential construction, the dominant wall-framing system built one story at a time on a completed floor platform is called:
Walls
What is the function of a header above a door or window in a load-bearing wall?
A jack stud (trimmer) differs from a king stud in that the jack stud:
Cripple studs are used primarily to:
Why are double top plates commonly used on wood-frame walls?
The most common on-center spacing for residential wall studs is:
Corner framing using three studs or a California corner is provided mainly to:
Fire blocking in wood-frame walls is installed primarily to:
Let-in bracing or structural sheathing is used in walls mainly to resist:
A nonbearing partition primarily supports:
When a double top plate joint occurs, the joint should be:
Actual dressed size of a standard 2×4 stud is approximately:
A load-bearing wall header for a wide opening is often built from doubled 2× stock with a plywood spacer so that the assembly matches:
Pressure-treated lumber is required for sill plates in contact with concrete primarily because:
When assembling a wall on the deck, studs should be crowned:
A wall that supports floor joists from the story above is classified as a:
Hold-down connectors and continuous rod systems at shear walls or braced wall lines primarily resist:
For a 3-foot-wide door with a 2-inch total side clearance allowance and 2-1/2-inch head allowance (example RO rule of thumb), the rough opening width would be closest to:
Loading more…