On CSWP Segment 1, what is the standard tolerance SOLIDWORKS allows on a requested mass value before your multiple-choice answer is counted wrong?
Part Modeling
Question · Medium
Before modeling the part in CSWP Segment 1, why should you set Document Properties units and decimal precision exactly as the question specifies?
Question · Easy
In Segment 1 a dimension named 'A' must always equal another dimension named 'B'. Which technique most reliably keeps them identical as values change?
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
Which SOLIDWORKS tool reports the mass, volume, surface area, and center of mass that Segment 1 questions ask you to read?
Mass depends directly on density. What must you do before reading a Segment 1 mass value to ensure it matches the expected answer?
A Segment 1 part must update correctly when a base width 'W' changes. Adding 'W' as a global variable first is recommended because it:
Which feature creates a solid by adding material along a path while a profile sweeps from one end of the path to the other?
In Segment 1 you must add a circular array of six identical holes about a central axis. Which feature is most efficient?
A Segment 1 sketch shows blue (under-defined) geometry. Why is fully defining the sketch important before later modifications?
Segment 1 instructs you to relate a hole's diameter to a global variable D using the rule diameter = D / 2. Where do you enter this rule?
Which feature hollows a solid part to a specified wall thickness while removing selected faces, common on Segment 1 enclosure parts?
After a Segment 1 dimension change, the model fails to rebuild with a feature error. What is the best first action?
Which feature blends between two or more sketched profiles on different planes to form a transitional solid such as a tapered funnel body?
A Segment 1 question asks for the part's center of mass coordinates. Relative to which reference are these coordinates reported by default?
Question · Hard
Why does the exam advise confirming the correct multiple-choice mass answer before moving to the next Segment 1 question?
Which feature spins a profile sketch a full or partial angle about a centerline to make axisymmetric parts such as shafts and pulleys?
On Segment 1 you must measure the angle between two model edges to verify geometry. Which tool gives this directly?
A Segment 1 equation references a dimension by name. Which naming convention does SOLIDWORKS use for a dimension named 'D1' in a sketch named 'Sketch1'?
Which evaluation confirms a part actually changed mass correctly after you edited a driving global variable in Segment 1?
The CSWP targets users with how much typical SOLIDWORKS experience, per the official program description?
Exam Overview
Which feature is best for adding a rounded transition along the intersection of two faces to reduce stress concentration on a Segment 1 part?
In an equation, which SOLIDWORKS syntax correctly references a previously defined global variable named 'Width'?
A Segment 1 part has a through hole that must always sit centered on a face whose size changes. Which approach keeps it centered automatically?
Which statement about the order of taking the three CSWP segments is correct?
When a Segment 1 question changes a global variable to a new value, what is the safest way to read the updated mass?
In CSWP Segment 2, a configuration is best described as:
Configurations
Where do you create and switch between configurations in SOLIDWORKS?
A design table in Segment 2 is most efficiently inserted through which menu path?
In a design table, which cell values control whether a feature is turned on or off for each configuration?
Segment 2 asks for the mass of configuration 'B'. What must you do before reading Mass Properties?
In Segment 2 you must add a feature that exists only in configuration 'Large' and not in 'Small'. Which configuration-aware setting accomplishes this?
Which statement about configuration-specific dimensions is correct for Segment 2?
Segment 2 instructs you to roll the model back and insert a new feature in the middle of the tree. Which tool lets you do this?
After editing a design table cell value in Segment 2, what makes the affected configuration update?
A Segment 2 question gives a new value for an equation-driven dimension across all configurations. Editing which item updates every configuration at once?
Which is a valid reason a feature might appear suppressed (grayed out) in the FeatureManager tree during Segment 2?
Segment 2 asks you to compare the mass of two configurations. What is the most reliable workflow?
A design table column header reads "$STATE@Boss-Extrude2". What does this column control?
Why does Segment 2 emphasize verifying you are in the correct configuration before each mass reading?
In Segment 2 you must change a chamfer to a fillet only in one configuration while keeping the chamfer in another. The cleanest approach is to:
Which statement about the number of configurations a part can hold is correct for Segment 2 work?
A Segment 2 question changes a dimension and asks for the new mass, but says to apply the change to all configurations. In the Modify dialog you should set the change scope to:
What is the benefit of using a design table over manually creating ten configurations in Segment 2?
During Segment 2 a parent feature is suppressed in a configuration. What happens to features that depend on it?
Which is the correct way to verify a design table actually created the expected configurations in Segment 2?
Segment 2 asks you to change material on one configuration only. Which capability supports per-configuration material?
Segment 2 totals roughly 50 minutes. What pacing habit best protects your score?
Loading more…