Under the 2021 IBC, a door must swing in the direction of egress travel when it serves an occupant load of how many or more?
Codes And Life Safety
Question · Medium
NCIDQ Exam Guide 2026: IDFX, IDIX & IDPX Study Plan
Free 2026 NCIDQ guide: PRAC is now IDIX. Current blueprints, question counts, CIDQ fees, April and October windows, pass rates, and a cycle-based study plan.
Blog
When fully open, a door may not project more than how many inches into the required width of an egress corridor under the 2021 IBC?
Question · Hard
Which edition of the accessibility standard is referenced together with the 2021 IBC for the 2026 NCIDQ code document?
Engineering Exam Prep Podcast
Listen on Spotify
Podcast
A circular turning space for a wheelchair under ICC A117.1-2017 must have a minimum clear diameter of what dimension?
The minimum clear width of a single accessible egress door opening, measured with the door open 90 degrees, is generally what dimension?
In the 2021 IBC, occupant load for a space is calculated by dividing the floor area by which value?
A fire-rated wall assembly is required to maintain its rating where ductwork penetrates it. Which device is specified to restore the rating at the penetration?
Which interior wall and ceiling finish flame-spread classification is the most restrictive (best performing) under ASTM E84?
The maximum allowable height of an accessible operable part such as a light switch, measured to a forward reach over an obstruction up to 20 inches deep, is what dimension under ICC A117.1-2017?
A common-path-of-egress-travel limit applies to which portion of the egress path?
An occupancy/life-safety plan prepared during implementation primarily communicates which information?
Question · Easy
Which occupancy classification under the 2021 IBC applies to a business office space?
The minimum required corridor width serving an occupant load of 50 or more in most commercial occupancies under the 2021 IBC is what dimension?
Which type of glazing is required at a hazardous location such as a door sidelite within 24 inches of a door under the 2021 IBC?
When two exits are required from a non-sprinklered space, the minimum separation between them is generally what fraction of the maximum overall diagonal dimension of the area served?
A toilet room is required to be accessible. The clear floor space at a wall-mounted accessible water closet centerline must be located what distance from the side wall under ICC A117.1-2017?
During implementation, integrating an under-counter appliance such as a refrigerator into a millwork run primarily requires coordinating which dimension first?
Integration And Ffe
Which document conveys the specific manufacturer, model, finish, and quantity of specified furniture for ordering?
When specifying upholstery fabric for seating in a hospitality lobby, which performance test result is most important to verify for durability?
A systems furniture (workstation) installation must coordinate electrical power. Power is typically delivered to the panels through which connection?
Which CSI MasterFormat division covers interior finishes such as gypsum board, tile, flooring, and painting?
Which MasterFormat division contains furniture, furnishings, and window treatments?
A ceiling-recessed light fixture in a fire-rated ceiling assembly may require which accessory to maintain the rating?
When integrating a wall-mounted television, the designer must coordinate in-wall blocking primarily to provide what?
A finish specified with a Class I rating per ASTM E648 (critical radiant flux) addresses which property of flooring?
A designer specifies acoustical ceiling panels and needs high sound absorption within the room. Which rating should be prioritized?
To limit speech privacy issues between two offices separated by a partition, the designer should specify a partition with a higher value of which rating?
When integrating sprinkler heads into a designed ceiling layout, the interior designer coordinates head placement primarily with which consultant?
A carpet tile specification calls out installation in a quarter-turn (ashlar) pattern primarily to achieve what?
Which property must be verified when specifying a resilient flooring product over an on-grade concrete slab?
In a construction drawing set, a plan that shows the layout of partitions with dimensions for locating new walls is called the:
Construction Documents
A reflected ceiling plan (RCP) is drawn as if the viewer is:
An interior elevation in a construction set primarily communicates:
A detail drawing in a construction set is typically drawn at a larger scale than plans in order to:
On a construction document, the symbol consisting of a circle divided by a horizontal line with a number above and a sheet number below is a:
A demolition plan should clearly distinguish elements to be removed by using which graphic convention?
On a partition (wall) type detail, the designation that identifies how a wall is built (studs, layers, height, rating) is keyed on the plan by a:
A partition is detailed to extend from the floor slab to the underside of the structural deck above. This is specified primarily to achieve:
In construction documentation, the term tolerance refers to:
A custom reception desk is documented with a millwork section detail. Which information is essential on that detail?
An accessible transaction counter (such as a portion of a reception desk) must provide a maximum height of what dimension under ICC A117.1-2017?
The drawing scale 1/4 inch equals 1 foot 0 inches expresses what relationship?
A keynote system on a drawing sheet is used to:
When a change is made to a drawing after issuance, the changed area is marked with a revision cloud and which additional symbol?
A dimension string on a partition plan is best located to dimension walls to which reference whenever possible?
Which drawing best documents the heights and profiles of crown molding and base trim transitions around a room?
Loading more…